






Trueseal 2K Paver & Stone Sealer – High Gloss
Paver & Stone Sealer
Ideal For
Driveways
Pool Decks
Walkways
RECOMMENDED SURFACES
Description
Trueseal 2K Paver & Stone Sealer – High Gloss
Trueseal 2K High Gloss is a two-component, water-based urethane clear sealer for concrete pavers, travertine, brick, flagstone and decorative concrete. It delivers the deepest color enhancement and highest sheen in the Trueseal line, with durability that outperforms one-part water-based and solvent-based sealers.
The cross-linking urethane formula cures to a hard, moisture-tolerant film that resists whitening, UV exposure and everyday wear for 2 to 3 years on driveways, pool decks and walkways. Low odor and low VOC, with water clean-up. Mixed working time is 90 to 120 minutes; dry to the touch in 2 to 6 hours, foot traffic in 12 to 24 hours, vehicle traffic in 72 hours at 70°F and 50% humidity.
Available in 1-gallon, 2.5-gallon and 5-gallon kits. Each kit includes Part A, Part B activator and a mixing bucket.
Preparation
Step 1Surface Preparation:
Surfaces must be clean, dry, sound, and free of dirt, dust, grease, oil, wax, soap film, rust, mold, mildew, curing compounds, and other contaminants that may interfere with adhesion. For best results, pressure wash at 2,500 PSI or greater.
Previously Painted Surfaces: Remove all loose, peeling, flaking, or chipped coatings. Trueseal 2K may be applied over firmly bonded existing coatings after the surface has been thoroughly cleaned and properly prepared.
Step 2Mixing:
Mix Part A and Part B together for 2 minutes using a stirring stick or a drill mixer equipped with a paddle attachment. Once mixed, the product will have a working time of approximately 90–120 minutes before it begins to harden.
Step 3Application:
Apply by brush, roller (minimum 3/8" nap), or spray. When rolling, use light to medium pressure and avoid excessive force. Apply evenly while minimizing puddles, lap marks, and roller trails.
At 70°F and 50% relative humidity, dry to the touch in approximately 2–6 hours and recoat in 3–6 hours. Allow 12–24 hours before foot traffic and 72 hours before vehicle traffic. Dry and cure times may vary depending on temperature, humidity, airflow, and weather conditions.
Trueseal 2K Paver & Stone Sealer – High Gloss
Trueseal 2K High Gloss is a two-component, water-based urethane clear sealer for concrete pavers, travertine, brick, flagstone and decorative concrete. It delivers the deepest color enhancement and highest sheen in the Trueseal line, with durability that outperforms one-part water-based and solvent-based sealers.
The cross-linking urethane formula cures to a hard, moisture-tolerant film that resists whitening, UV exposure and everyday wear for 2 to 3 years on driveways, pool decks and walkways. Low odor and low VOC, with water clean-up. Mixed working time is 90 to 120 minutes; dry to the touch in 2 to 6 hours, foot traffic in 12 to 24 hours, vehicle traffic in 72 hours at 70°F and 50% humidity.
Available in 1-gallon, 2.5-gallon and 5-gallon kits. Each kit includes Part A, Part B activator and a mixing bucket.
Step 1Surface Preparation:
Surfaces must be clean, dry, sound, and free of dirt, dust, grease, oil, wax, soap film, rust, mold, mildew, curing compounds, and other contaminants that may interfere with adhesion. For best results, pressure wash at 2,500 PSI or greater.
Previously Painted Surfaces: Remove all loose, peeling, flaking, or chipped coatings. Trueseal 2K may be applied over firmly bonded existing coatings after the surface has been thoroughly cleaned and properly prepared.
Step 2Mixing:
Mix Part A and Part B together for 2 minutes using a stirring stick or a drill mixer equipped with a paddle attachment. Once mixed, the product will have a working time of approximately 90–120 minutes before it begins to harden.
Step 3Application:
Apply by brush, roller (minimum 3/8" nap), or spray. When rolling, use light to medium pressure and avoid excessive force. Apply evenly while minimizing puddles, lap marks, and roller trails.
At 70°F and 50% relative humidity, dry to the touch in approximately 2–6 hours and recoat in 3–6 hours. Allow 12–24 hours before foot traffic and 72 hours before vehicle traffic. Dry and cure times may vary depending on temperature, humidity, airflow, and weather conditions.
Two-part technology
What is a two-part sealer?
Most paver sealers are one part: you open the can and the sealer simply dries as the water or solvent evaporates. Trueseal 2K is different. Part A (the sealer) and Part B (the activator) are mixed right before you apply, and the two react to cure into a true urethane film — the same chemistry used on garage floors and marine finishes.
-
One extra step. That’s it.Pour in Part B, stir, and apply within 90 minutes. Everything else — prep, rolling, cleanup — is exactly what you’d do with a one-part.
-
Tough, Crosslinking FinishThe Part B crosslinks the sealer into one locked-together film instead of loose resin that dries on top. The result is a hard, scuff-resistant surface that one-part sealers can’t match.
-
Don’t be afraid of the mixIt’s one extra step, and it’s what separates a pro-grade finish from a hardware-store sealer. Stir in Part B and apply like any other coating.

Part A
This is the acrylic Part A component of the Trueseal 2K system and is designed to be mixed with Part B before use. It is packaged for easy, accurate mixing, including when splitting the kit into smaller batches.
Mixing Bucket
All components come self-contained in a convenient mixing bucket, making it easy to combine and mix Part A and Part B before application.
Part B (Activator)
This is the urethane activator (Part B) component of the Trueseal 2K system and is designed to be mixed with Part A before use. It is packaged for easy, accurate mixing, including when splitting the kit into smaller batches.









